HP PCL PRINTER CODES

return to original page

HP LaserJet Printers – PCL Commands, Basic Page Formatting, and Font Selection

In this document:
Introduction

About using these commands

Job control commands

Page control commands

Contact HP?

Introduction
This document lists the HP LaserJet Printer Command Language (PCL) printer commands for basic page formatting and font selection. It is intended as a general guide.

PCL defines a standard set of commands enabling programs to communicate with HP or HP-compatible printers. For further information about PCL commands, HP-GL/2, macros, or PJL commands, use the Technical Reference Manual set, part number 5021-0377. Order the manual set from HP’s Support Materials Organization.

NOTE: To order Parts, Supplies, and Accessories, contact the nearest authorized HP dealer or reseller. Click here to go to a list of Dealer locator phone numbers, or refer to the User’s Guide that came with the HP product.

About using these commands
Some Paper Source and Page Size commands may not work all printers.
CAUTION: Some products require different Paper Source and Page Size commands than those that are contained in this document. For some applications it may be necessary to get support on specific PCL commands from the application manufacturer.

For supported paper tray and paper size options, see the User’s Manual or check the product Web site.
The commands are listed in hierarchical order and give the decimal and hexadecimal equivalents.
Values in the parentheses (x) identify the lower case of the termination character that is used for combining commands.
Ec represents the escape character for the software. In DOS Edit, Ec is represented by holding down the CTRL key and pressing the letter P. Release both keys, and press the ESC key.
The symbols, # and #…#, are variables that are replaced with the numbers needed for a document.
Example
To set the number of copies to 14, Ec&l#X, replace the # or #…# with the following:

ASCII
14

Decimal
049 052

Hexadecimal
31 34

Use the following table to help translate into decimal or hexadecimal:

ASCII Value
Hex
Dec
Description

0
30
48
Zero

1
31
49
One

2
32
50
Two

3
33
51
Three

4
34
52
Four

5
35
53
Five

6
36
54
Six

7
37
55
Seven

8
38
56
Eight

9
39
57
Nine

2E
46
Period (point)

Job control commands
Function
Parameter
Command
Decimal Value
Hexadecimal Value
Reset

Function

Parameter

Command

Decimal Value
Hexadecimal Value

Reset
EcE
027 069
1B 45

Number of Copies
# of Copies (1 – 99)
Ec&l#X (x)
027 038 108 #…# 088 (120)
1B 26 6C #. # 58 (78)

Unit of Measure
# = Number of units per inch
Ec&u#D (d)
027 038 117 #…# 068 (100)
1B 26 75 #…# 44 (64)

Simplex/Duplex operation
NOTE: This is only applicable to duplex capable printers.

Function

Parameter

Command
Decimal Value

Hexadecimal Value

Simplex Print
Simplex
Ec&l0S (s)
027 038 108 048 083 (115)
1B 26 6C 30 53 (73)

Duplex Print
Long-Edge Binding
Ec&l1S (s)
027 038 108 049 083 (115)
1B 26 6C 31 53 (73)

Short-Edge Binding
Ec&l2S (s)
027 038 108 050 083 (115)
1B 26 6C 32 53 (73)

Long-Edge (left) Offset Registration
# of Decipoints (1/720″)
Ec&l#U (u)
027 038 108 #…# 085 (117)
1B 26 6C #…# 55 (75)

Short-Edge (Top) Offset Registration
# of Decipoints (1/720″)
Ec&l#Z (z)
027 038 108 #…# 090 (122)
1B 26 6C #…# 5A (7A)

Page Side Selection
Next Side
Ec&a0G (g)
027 038 097 048 071 (103)
1B 26 61 30 47 (67)

Front Side
Ec&a1G (g)
027 038 097 049 071 (103)
1B 26 61 31 47 (67)

Back Side
Ec&a2G (g)
027 038 097 050 071 (103)
1B 26 61 32 47 (67)

Page control commands
Function
Parameter
Command
Decimal Value
Hexadecimal Value
Paper destination

Function
Command
Decimal Value
Hexadecimal Value

Auto Select
Ec&l0G
027 038 108 048 103 (71)
1B 26 6C 30 67 (47)

Top Output Bin
Ec&l1G
027 038 108 049 103 (71)
1B 26 6C 31 67 (47)

Left Output Bin
Ec&l2G
027 038 108 050 103 (71)
1B 26 6C 32 67 (47)

Optional multi-bin mailbox (HP LaserJet 5Si, 5Si MX, and 5Si NX)

Function
Command
Decimal Value
Hexadecimal Value

Left Bin Face Up
Ec&l3G
027 038 108 051 103 (71)
1B 26 6C 33 67 (47)

Bin 1 Face Down
Ec&l4G
027 038 108 052 103 (71)
1B 26 6C 34 67 (47)

Bin 2 Face Down
Ec&l5G
027 038 108 053 103 (71)
1B 26 6C 35 67 (47)

Bin 3 Face Down
Ec&l6G
027 038 108 054 103 (71)
1B 26 6C 36 67 (47)

Bin 4 Face Down
Ec&l7G
027 038 108 055 103 (71)
1B 26 6C 37 67 (47)

Bin 5 Face Down
Ec&l8G
027 038 108 056 103 (71)
1B 26 6C 38 67 (47)

Bin 6 Face Down
Ec&l9G
027 038 108 057 103 (71)
1B 26 6C 39 67 (47)

Bin 7 Face Down
Ec&l10G
027 038 108 049 048 103 (71)
1B 26 6C 31 31 67 (47)

Bin 8 Face Down
Ec&l11G
027 038 108 049 049 103 (71)
1B 26 6C 31 32 67 (47)

Optional mailbox with stapler (HP LaserJet 5Si Mopier)

Function
Command
Decimal Value
Hexadecimal Value

Left Bin Face Up
Ec&l2G
027 038 108 050 103 (71)
1B 26 6C 32 67 (47)

Bin 1 Face Down
Ec&l3G
027 038 108 051 103 (71)
1B 26 6C 33 67 (47)

Bin 2 Face Down
Ec&l4G
027 038 108 052 103 (71)
1B 26 6C 34 67 (47)

Bin 3 Face Down
Ec&l5G
027 038 108 053 103 (71)
1B 26 6C 35 67 (47)

Bin 4 Face Down
Ec&l6G
027 038 108 054 103 (71)
1B 26 6C 36 67 (47)

Bin 5 Face Down
Ec&l7G
027 038 108 055 103 (71)
1B 26 6C 37 67 (47)

Stapler Bin (Printer is in Mailbox mode)
Ec&l9G
027 038 108 057 103 (71)
1B 26 6C 39 67 (47)

Stapler Bin (Printer is in Stacker or Separator mode)
Ec&l8G
027 038 108 053 103 (71)
1B 26 6C 35 67 (47)

Paper source, length, and size
CAUTION: Some products require different Paper Source and Page Size commands than those that are contained in this document. This information may be found in documentation specific to those products.

Function
Parameter
Command
Decimal Value
Hexadecimal Value

Paper Source
Eject Page
Ec&l0H (h)
027 038 108 048 072 (104)
1B 26 6C 30 48 (68)

Paper Cassette
Ec&l1H (h)
027 038 108 049 072 (104)
1B 26 6C 31 48 (68)

Paper Cassette / tray 2
Ec&l1H (h)
027 038 108 049 072 (104)
1B 26 6C 31 48 (68)

Manual Feed Paper
Ec&l2H (h)
027 038 108 050 072 (104)
1B 26 6C 32 48 (68)

Manual Feed Envelope
Ec&l3H (h)
027 038 108 051 072 (104)
1B 26 6C 33 48 (68)

Tray 1
Ec&l8H (h)
027 038 108 056 072 (104)
1B 26 6C 38 48 (68)

Optional 500/ 2000 Sheet Lower Cassette
Ec&l5H (h)
027 038 108 053 072 (104)
1B 26 6C 35 48 (68)

MP Tray/ Tray 3
Ec&l4H (h)
027 038 108 052 072 (104)
1B 26 6C 34 48 (68)

Envelope Feeder
Ec&l6H (h)
027 038 108 054 072 (104)
1B 26 6C 36 48 (68)

Page Size
Executive
Ec&l1A (a)
027 038 108 049 065 (097)
1B 26 6C 31 41 (61)

JISEXEC (8.5 X 13 )
Ec&l8A (a)
027 038 108 056 065 (097)
1B 26 6C 38 41 65 (61)

Letter
Ec&l2A (a)
027 038 108 050 065 (097)
1B 26 6C 32 41 (61)

Legal
Ec&l3A (a)
027 038 108 051 065 (097)
1B 26 6C 33 41 (61)

Tabloid (11 X 17)
Ec&l6A (a)
027 038 108 054 065 (097)
1B 26 6C 36 41 (61)

A4
Ec&l26A (a)
027 038 108 050 054 065 (097)
1B 26 6C 32 36 41 (61)

Function
Parameter
Command
Decimal Value
Hexadecimal Value

A3
Ec&l27A (a)
027 038 108 050 055 065 (097)
1B 26 6C 32 37 41 (61)

A5
Ec&l4A (a)
027 038 108 052 065 (097)
1B 26 6C 34 41 (61)

JIS B5
Ec&l45A (a)
027 038 108 052 053 065 (097)
1B 26 6C 34 35 41 (61)

JIS B4
Ec&l46A (a)
027 038 108 052 054 065 (097)
1B 26 6C 34 36 41 (61)

JPOST
Ec&l71A (a)
027 038 108 055 049 065 (097)
1B 26 6C 37 31 41 (61)

JPOSTD
Ec&l72A (a)
027 038 108 055 050 065 (097)
1B 26 6C 37 32 41 (61)

Monarch
Ec&l80A (a)
027 038 108 056 048 065 (097)
1B 26 6C 38 30 41 (61)

COM 10
Ec&l81A (a)
027 038 108 056 049 065 (097)
1B 26 6C 38 31 41 (61)

B5
Ec&l100A(a)
027 038 108 049 048 048 065 (097)
1B 26 6C 31 30 30 41 (61)

Custom/
Maximum
Ec&l101A(a)
027 038 108 049 048 049 065 (097)
1B 26 6C 31 30 32 41 (61)

DL
Ec&l90A (a)
027 038 108 057 048 065 (097)
1B 26 6C 39 30 41 (61)

C5
Ec&l91A (a)
027 038 108 057 049 065 (097)
1B 26 6C 39 31 41 (61)

Page Length
# if Lines (5-128)
Ec&l#P (p)
027 038 108 #…# 080 (112)
1B 26 6C #…# 50 (70)

Orientation

Function
Parameter
Command
Decimal Value
Hexadecimal Value

Orientation
Portrait
Ec&l0O (o)
027 038 108 048 079 (111)
1B 26 6C 30 4F (6F)

Landscape
Ec&l1O (o)
027 038 108 049 079 (111)
1B 26 6C 31 4F (6F)

Reverse Portrait
Ec&l2O (o)
027 038 108 050 079 (111)
1B 26 6C 32 4F (6F)

Reverse Landscape
Ec&l3O (o)
027 038 108 051 079 (111)
1B 26 6C 33 4F (6F)

Print Direction
Number of Degrees of Rotation counter-
clockwise (90 degree increments only)
Ec&a#P
027 038 097 #…# 080 (112)
1B 26 61 #…# 50 (70)

Margins and text length

Function
Parameter
Command
Decimal Value
Hexadecimal Value

Top Margin
Number of Lines
Ec&l#E (e)
027 038 108 #…# 069 (101)
1B 26 6C #…# 45 (65)

Text Length
Number of Lines
Ec&l#F (f)
027 038 108 #…# 070 (102)
1B 26 6C #…# 46 (66)

Left Margin
Number of Columns
Ec&a#L (l)
027 038 097 #…# 076 (108)
1B 26 61 #…# 4C (6C)

Right Margin
Number of Columns
Ec&a#M (m)
027 038 097 #…# 077 (109)
1B 26 61 #…# 4D (6D)

Clear Horizontal Margins
Ec9
027 057
1B 39

Perforation skip mode

Function
Parameter
Command
Decimal Value
Hexadecimal Value

Perforation Skip
Disable
EC&l0L (l)
027 038 108 048 076 (108)
1B 26 6C 30 4C (6C)

Enable
EC&l1L (l)
027 038 108 049 076 (108)
1B 26 6C 31 4C (6C)

Horizontal column spacing

Horizontal Motion Index (HMI)
Number of .0083-inch Increments
Ec&k#H (h)
027 038 107 #…# 072 (104)
1B 26 6B #…# 48 (68)

The Horizontal Motion Index (HMI) command designates the distance between columns in .0083-inch increments. When fixed pitch fonts are selected, all printable characters, including the space and backspace characters, are affected by HMI. When proportional fonts are selected, the HMI affects only the control code space character. The default HMI is equal to the pitch value in the font header. The printer escape sequence to be sent is as follows:

Ec&k#H # is equal to a variable that is derived from the following formula:

Horizontal Printable Area
———————————— X 120 = #
Desired characters per line

If the desired pitch or number of characters per horizontal inch is known, use the following formula:

120/Desired characters per inch = #

Vertical line spacing

Vertical Motion Index (VMI)

# of .0208-inch Increments

Ec&l#C (c)

027 038 108 #…# 067 (99)
1B 26 6C #…# 43 (63)

The Vertical Motion Index (VMI) command designates the distance between rows in .0208-inch increments (the vertical distance that the cursor will move for a line feed operation). This command affects the line feed and half-line feed spacing. The factory default VMI is eight, which corresponds to six lines per inch. VMI can be selected from the printer control panel or by sending a printer escape sequence: Ec&#C . # is equal to a variable that is derived from the following formula:

Vertical Printable Area
———————————- X 48 = #
Desired Lines Per Page

Note: Use either VMI (most precise method of line spacing) or Lines per inch, as only the last command will execute.

Line Spacing (Lines per inch)

1 line/inch

Ec&l1D (d)

027 038 108 049 068 (100)

1B 26 6C 31 44 (64)

2 lines/inch
Ec&l2D (d)
027 038 108 050 068 (100)
1B 26 6C 32 44 (64)

3 lines/inch
Ec&l3D (d)
027 038 108 051 068 (100)
1B 26 6C 33 44 (64)

4 lines/inch
Ec&l4D (d)
027 038 108 052 068 (100)
1B 26 6C 34 44 (64)

6 lines/inch
Ec&l6D (d)
027 038 108 054 068 (100)
1B 26 6C 36 44 (64)

8 lines/inch
Ec&l8D (d)
027 038 108 056 068 (100)
1B 26 6C 38 44 (64)

12 lines/inch
Ec&l12D (d)
027 038 108 049 050 068 (100)
1B 26 6C 31 32 44 (64)

16 lines/inch
Ec&l16D (d)
027 038 108 049 054 068 (100)
1B 26 6C 31 36 44 (64)

24 lines/inch
Ec&l24D (d)
027 038 108 050 052 068 (100)
1B 26 6C 32 34 44 (64)

48 lines/inch
Ec&l48D (d)
027 038 108 052 056 068 (100)
1B 26 6C 34 38 44 (64)

Vertical and horizontal

Function
Parameter
Command
Decimal Value
Hexadecimal Value

Vertical Position
# of Rows
Ec&a#R (r)
027 038 097 #…# 082 (114)
1B 26 61 #…# 52 (72)

Superscript
Up ¼ Row
Ec&a-.25R (r)
027 038 097 045 046 050 053 082 (114)
1B 26 61 2D 2E 32 35 52 (72)

Subscript
Down ¼ Row
Ec&a+.25R (r)
027 038 097 043 046 050 053 082 (114)
1B 26 61 2B 2E 32 35 52 (72)

# of Dots
Ec*p#Y (y)
027 042 112 #…# 089 (121)
1B 2A 70 #…# 59 (79)

# of Decipoints
Ec&a#V (v)
027 038 097 #…# 086 (118)
1B 26 61 #…# 56 (76)

Horizontal Position
# of Columns
Ec&a#C (c)
027 038 097 #…# 067 (99)
1B 26 61 #…# 43 (63)

# of Dots
Ec*p#X (x)
027 042 112 #…# 088 (120)
1B 2A 70 #…# 58 (78)

# of Decipoints
Ec&a#H (h)
027 038 097 #…# 072 (104)
1B 26 61 #…# 48 (68)

Half Line Feed
Ec=
027 061
1B 3D

Half Line Feed
Ec=
027 061
1B 3D

End-of-line termination

Function
Parameter
Command
Decimal Value
Hexadecimal Value

Line Termination
CR=CR;LF=LF; FF=FF
Ec&k0G (g)
027 038 107 048 071 (103)
1B 26 6B 30 47 (67)

CR=CR+LF;LF=LF FF=FF
Ec&k1G (g)
027 038 107 049 071 (103)
1B 26 6B 31 47 (67)

CR=CR; LF=CR+LF; FF=CR+FF
Ec&k2G (g)
027 038 107 050 071 (103)
1B 26 6B 32 47 (67)

CR=CR+LF; LF=CR+LF; FF=CR+FF
Ec&k3G (g)
027 038 107 051 071 (103)
1B 26 6B 33 47 (67)

Symbol set selection

Function

Parameter

Command

Decimal Value

Hexadecimal Value

Primary Symbol Set
ISO 60: Norwegian
Ec(0D
027 040 048 068
1B 28 30 44

ISO 4: United Kingdom
Ec(1E
027 040 049 069
1B 28 31 45

Windows 3.1

Latin 2
Ec(9E
027 040 057 069
1B 28 39 45

ISO 69: French
Ec(1F
027 040 049 070
1B 28 31 46

ISO 21: German
Ec(1G
027 040 049 071
1B 28 31 47

ISO 15: Italian
Ec(0I
027 040 048 073
1B 28 30 49

Microsoft (R) Publishing
Ec(6J
027 040 054 074
1B 28 36 4A

DeskTop
Ec(7J
027 040 055 074
1B 28 37 4A

PS Text
Ec(10J
027 040 049 048 074
1B 28 31 30 4A

Function

Parameter

Command
Decimal Value
Hexadecimal Value

MC Text
Ec(12J
027 040 049 050 074
1B 28 31 32 4A

Ventura International
Ec(13J
027 040 049 051 074
1B 28 31 33 4A

Ventura US
Ec(14J
027 040 049 052 074
1B 28 31 34 4A

Wingdings
Ec(579L
027 040 053 055 057 076
1B 28 35 37 39 4C

PS Math
Ec(5M
027 040 053 077
1B 28 35 4D

Ventura Math
Ec(6M
027 040 054 077
1B 28 36 4D

Math-8
Ec(8M
027 040 056 077
1B 28 38 4D

Symbol
Ec(19M
027 040 049 057 077
1B 28 31 39 4D

ISO 8859-1 (ECMA-94) Latin 1
Ec(0N
027 040 048 078
1B 28 30 4E

ISO 8859-2: Latin 2
Ec(2N
027 040 050 078
1B 28 32 4E

ISO 8859-9: Latin 5
Ec(5N
027 040 053 078
1B 28 35 4E

ISO 11: Swedish
Ec(0S
027 040 048 083
1B 28 30 53

ISO 17: Spanish
Ec(2S
027 040 050 083
1B 28 32 53

Windows 3.1 Latin 5
Ec(5T
027 040 053 084
1B 28 35 54

PC Turkish
Ec(9T
027 040 057 084
1B 28 39 54

Function

Parameter

Command
Decimal Value
Hexadecimal Value

ISO 6: ASCII
Ec(0U
027 040 048 085
1B 28 30 55

Legal
Ec(1U
027 040 049 085
1B 28 31 55

Roman-8
Ec(8U
027 040 056 085
1B 28 38 55

Windows 3.0 Latin 1
Ec(9U
027 040 057 085
1B 28 39 55

PC-8
Ec(10U
027 040 049 048 085
1B 28 31 30 55

PC-8 D/N
Ec(11U
027 040 049 049 085
1B 28 31 31 55

PC 850
Ec(12U
027 040 049 050 085
1B 28 31 32 55

Pi Font
Ec(15U
027 040 049 053 085
1B 28 31 35 55

PC-852
Ec(17U
027 040 049 055 085
1B 28 31 37 55

Windows 3.1

Latin 1 (ANSI)
Ec(19U
027 040 049 057 085
1B 28 31 39 55

NOTE: Refer to the PCL-5 Comparison Guide for additional supported symbol sets.

Spacing

Function
Parameter
Command
Decimal Value
Hexadecimal Value

Primary Spacing
Fixed
Ec(s0P (p)
027 040 115 048 080 (112)
1B 28 73 30 50 (70)

Proportional
Ec(s1P (p)
027 040 115 049 080 (112)
1B 28 73 31 50 (70)

Pitch

Function
Parameter
Command
Decimal Value
Hexadecimal Value

Primary Pitch
Number Characters per inch
Ec(s#H (h)
027 040 115 #…# 072 (104)
1B 28 73 #…# 48 (68)

Set Pitch Mode
10
Ec&k0S (s)
027 038 107 048 083 (115)
1B 26 6B 30 53 (73)

Compressed (16.5-16.7)
Ec&k2S (s)
027 038 107 050 083 (115)
1B 26 6B 32 53 (73)

Elite (12.0)
Ec&k4S (s)
027 038 107 052 083 (115)
1B 26 6B 34 53 (73)

Point size

Function
Parameter
Command
Decimal Value
Hexadecimal Value

Primary Height
# Points
Ec(s#V (v)
027 040 115 #…# 086 (118)
1B 28 73 #…# 56 (76)

Style

Function

Parameter

Command

Decimal Value
Hexadecimal Value

Primary Style
Upright (Solid)
Ec(s0S (s)
027 040 115 048 083 (115)
1B 28 73 30 53 (73)

Italic
Ec(s1S (s)
027 040 115 049 083 (115)
1B 28 73 31 53 (73)

Condensed
Ec(s4S (s)
027 040 115 052 083 (115)
1B 28 73 34 53 (73)

Condensed Italic
Ec(s5S (s)
027 040 115 053 083 (115)
1B 28 73 35 53 (73)

Compressed (Extra Condensed)
Ec(s8S (s)
027 040 115 056 083 (115)
1B 28 73 38 53 (73)

Expanded
Ec(s24S (s)
027 040 115 050 052 083 (115)
1B 28 73 32 34 53 (73)

Outline
Ec(s32S (s)
027 040 115 051 050 083 (115)
1B 28 73 33 32 53 (73)

Inline
Ec(s64S (s)
027 040 115 054 052 083 (115)
1B 28 73 36 34 53 (73)

Shadowed
Ec(s128S (s)
027 040 115 049 050 056 083 (115)
1B 28 73 31 32 38 53 (73)

Outline Shadowed
Ec(s160S (s)
027 040 115 049 054 048 083 (115)
1B 28 73 31 36 30 53 (73)

Additional style values may be obtained from the related documentation provided with HP’s font products.

PCL 5 HP LaserJet printers allow complex structures (contours, outlines, shading, etc.) and widths, as well as posture to be specified. Refer to the HP PCL 5 Printer Language Technical Reference Manual.

Stroke weight

Function
Parameter
Command
Decimal Value
Hexadecimal Value

Primary Font Stroke Weight
Ultra Thin
Ec(s-7B (b)
027 040 115 045 055 066 (98)
1B 28 73 2D 37 42 (62)

Extra Thin
Ec(s-6B (b)
027 040 115 045 054 066 (98)
1B 28 73 2D 36 42 (62)

Thin
Ec(s-5B (b)
027 040 115 045 053 066 (98)
1B 28 73 2D 35 42 (62)

Extra Light
Ec(s-4B (b)
027 040 115 045 052 066 (98)
1B 28 73 2D 34 42 (62)

Light
Ec(s-3B (b)
027 040 115 045 051 066 (98)
1B 28 73 2D 33 42 (62)

Demi Light
Ec(s-2B (b)
027 040 115 045 050 066 (98)
1B 28 73 2D 32 42 (62)

Semi Light
Ec(s-1B (b)
027 040 115 045 049 066 (98)
1B 28 73 2D 31 42 (62)

Medium (book or text)
Ec(s0B (b)
027 040 115 048 066 (98)
1B 28 73 30 42 (62)

Semi Bold
Ec(s1B (b)
027 040 115 049 066 (98)
1B 28 73 31 42 (62)

Demi Bold
Ec(s2B (b)
027 040 115 050 066 (98)
1B 28 73 32 42 (62)

Bold
Ec(s3B (b)
027 040 115 051 066 (98)
1B 28 73 33 42 (62)

Extra Bold
Ec(s4B (b)
027 040 115 052 066 (98)
1B 28 73 34 42 (62)

Black
Ec(s5B (b)
027 040 115 053 066 (98)
1B 28 73 35 42 (62)

Extra Black
Ec(s6B (b)
027 040 115 054 066 (98)
1B 28 73 36 42 (62)

Ultra Black
Ec(s7B (b)
027 040 115 055 066 (98)
1B 28 73 37 42 (62)

Primary typeface family

Function
Parameter
Command
Decimal Value
Hexadecimal Value

LinePrinter
Ec(s0T
027 040 115 048 084 (116)
1B 28 73 30 54 (74)

Typeface Family
Albertus
Ec(s4362T (t)
027 040 115 052 051 054 050 084 (116)
1B 28 73 34 33 36 32 54 (74)

Antique Olive
Ec(s4168T (t)
027 040 115 052 049 054 056 084 (116)
1B 28 73 34 31 36 38 54 (74)

Clarendon
Ec(s4140T (t)
027 040 115 052 049 052 048 084 (116)
1B 28 73 34 31 34 30 54 (74)

Coronet
Ec(s4116T (t)
027 040 115 052 049 049 054 084 (116)
1B 28 73 34 31 31 36 54 (74)

Courier
Ec(s4099T (t)
027 040 115 052 048 057 057 084 (116)
1B 28 73 34 30 39 39 54 (74)

Garamond Antiqua
Ec(s4197T (t)
027 040 115 052 049 057 055 084 (116)
1B 28 73 34 31 39 37 54 (74)

Letter Gothic
Ec(s4102T (t)
027 040 115 052 049 048 050 084 (116)
1B 28 73 34 31 30 32 54 (74)

Marigold
Ec(s4297T (t)
027 040 115 052 050 057 055 084 (116)
1B 28 73 34 32 39 37 54 (74)

CG Omega
Ec(s4113T (t)
027 040 115 052 049 049 051 084 (116)
1B 28 73 34 31 31 33 54 (74)

CG Times
Ec(s4101T (t)
027 040 115 052 049 048 049 084 (116)
1B 28 73 34 31 30 31 54 (74)

Univers
Ec(s4148T (t)
027 040 115 052 049 052 056 084 (116)
1B 28 73 34 31 34 38 54 (74)

Arial (R)
Ec(s16602T (t)
027 040 115 049 054 054 048 050 084 (116)
1B 28 73 31 36 36 30 32 54 (74)

Times New Roman
Ec(s16901T (t)
027 040 115 049 054 057 048 049 084 (116)
1B 28 73 31 36 39 30 31 54 (74)

Symbol
Ec(s16686T (t)
027 040 115 049 054 054 056 054 084 (116)
1B 28 73 31 36 36 38 36 54 (74)

Wingdings
Ec(s31402T (t)
027 040 115 051 049 052 048 050 084 (116)
1B 28 73 33 31 34 30 32 54 (74)

Underline

Function
Parameter
Command
Decimal Value
Hexadecimal Value

Underline
Enable Fixed
Ec&d0D (d)
027 038 100 048 068 (100)
1B 26 64 30 44 (64)

Enable Floating
Ec&d3D (d)
027 038 100 051 068 (100)
1B 26 64 33 44 (64)

Disable
Ec&d@
027 038 100 064
1B 26 64 40

Contact HP?
Find the nearest service center
Buy HP (United States)
Buy HP (Outside the United States

Arial (R) is a U.S. registered trademark of the
Monotype Corporation.

Microsoft (R) is a U.S. registered trademark of
Microsoft Corp.

Windows (R) and MS Windows (R) are U.S.
registered trademarks of Microsoft Corp.

Times Roman (TM) is a trademark of
Linotype-Hell AG and/or its
subsidiaries in the U.S. and other countries.

Copyright (C) Hewlett-Packard Co. 1997
This information is subject to change without notice and
is provided “as is” with no warranty.
Hewlett-Packard shall not be liable for any direct,
indirect, special, incidental or consequential damages
in connection with the use of this material.